DSC Power608 Especificações descarregar pdf (Página 44)

R E P O R T I N G C O D E S

Table 2

Contact ID Zone Alarm/Restoral Event Codes

(as per ADEMCO):

Program any of these codes for zone alarms/restorals when

using the standard (non-automatic) Contact ID reporting format.

Medical Alarms

(1)AA Medical

(1)A1 Pendant Transmitter

(1)A2 Fail to Report In

Fire Alarms

(1)1A Fire Alarm

(1)11 Smoke

(1)12 Combustion

(1)13 Water Flow

(1)14 Heat

(1)15 Pull Station

(1)16 Duct

(1)17 Flame

(1)18 Near Alarm

Panic Alarms

(1)2A Panic

(1)21 Duress

(1)22 Silent

(1)23 Audible

Burglar Alarms

(1)3A Burglary

(1)31 Perimeter

(1)32 Interior

(1)33 24 Hour

(1)34 Entry / Exit

(1)35 Day / Night

(1)36 Outdoor

(1)37 Tamper

(1)38 Near Alarm

General Alarms

(1)4A General Alarm

(1)43 Exp. module failure

(1)44 Sensor tamper

(1)45 Module Tamper

(1)4A Cross Zone Police Code

24 Hour Non-Burglary

(1)5A 24 Hour non-Burg

(1)51 Gas detected

(1)52 Refrigeration

(1)53 Loss of Heat

(1)54 Water Leakage

(1)55 Foil Break

(1)56 Day Trouble

(1)57 Low bottled Gas level

(1)58 High Temp

(1)59 Low Temp

(1)61 Loss of Air Flow

Table 3

SIA Format Automatic Zone Alarm/Restoral Codes

Zone Definition SIA Auto Rep

Codes*

Zone Alm/Rest.

Delay, Instant, Interior, Delay

Stay/Away, Interior Stay/Away,

24Hr Burg.

BA-ZZ/BH-ZZ

Standard 24Hr Fire, Delayed 24Hr

Fire

FA-ZZ/FH-ZZ

24Hr Supervisory US-ZZ/UR-ZZ

24Hr Supervisory Buzzer UA-ZZ/UH-ZZ

24Hr Sprinkler SA-ZZ/SH-ZZ

24Hr Gas GA-ZZ/GH-ZZ

24Hr Heat KA-ZZ/KH-ZZ

24Hr Medical MA-ZZ/MH-ZZ

24Hr Emergency (non-medical) QA-ZZ/QH-ZZ

24Hr Waterflow WA-ZZ/WH-ZZ

24Hr Freeze ZA-ZZ/ZH-ZZ

24Hr Holdup HA-ZZ/HH-ZZ

24Hr Panic PA-ZZ/PH-ZZ

Latching 24Hr BA-ZZ/BH-ZZ

* ZZ = zones 01-08

Section

Reporting Code Code Sent When... Dialer

Direction*

Contact

ID Codes

SIA Auto Rep

Codes**

[349-350]

AC Line Trouble/Rest. AC power to control panel is disconnected or interrupted/AC

power restored (Both codes follow AC Failure Comm. Delay.)

MA/R (3) A1 AT-00/AR-00

[349-350]

Main Bell Trouble/Rest. open circuit detected across bell terminals/bell circuit closed MA/R (3) 21 UT-99/UJ-99

[349-350]

Fire Trouble/Rest. a trouble occurs/restores on a fire zone MA/R (3) 73 FT-00/FJ-00

[349-350]

Auxiliary Power Trouble/Rest. aux voltage supply trouble/restoral MA/R (3) AA YP-00/YQ-00

[349]

TLM Failure telephone line monitoring trouble (sent via LINKS. Do not

program if LINKS not used)

MA/R (3) 51 LT-00

[350]

TLM Restore Telephone line trouble restore MA/R (3) 51 LR-00

[349-350]

Gen System Supervisory

Trouble/Rest.

control panel loses/restores communications with module(s)

connected to the Keybus

MA/R (3) 33 ET-00/ER-00

[349-350]

General System Trouble/Restore "Service Required"trouble occurs (view troubles using [*][2][3])/

troubles restored

MA/R (3) 3A YX-00/YZ-00

[351]

Line 1 or 2 FTC Restoral control panel has restored communications to central station on

line 1or 2 (after FTC)

MA/R (3) 54 YK-00

[351]

Event Buffer is 75% Full event buffer is almost full since last upload MA/R (6) 23 JL-00

[351]

DLS Lead In downloading session start MA/R (4) 11 RB-00

[351]

DLS Lead Out downloading session complete MA/R (4) 12 RS-00

[351]

General Zone Trouble/Rest. one or more zones have trouble/trouble restored MA/R (3) 72 UT-00/UJ-00

[351]

Delinquency programmed amount of time (days or hours) for delinquency has

expired without zone activity or without system being armed

MA/R (4) 54† CD-00

[352]

Periodic Test periodic sytem test transmission T (6) A2 RP-00

[352]

System Test [*][6] bell/communications test T (6) A1 RX-00

[352]

LINKS Test LINKS test transmission T (6) A3 TX-00

[353]

General Device Low Battery

Trouble/Rest.

Wireless zones/pendants (WLS908);

handheld keypads (WLS910); wireless keys (WLS909) have low

battery/all low batteries restored

MA/R (3) 84 XT-00/XR-00

* A/R = alarms/restorals;T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions

** UU = user number (user01-42); ZZ = zone number (01-08)

†Program the “Fail to close” event code [(4)54] to report either closing or activity delinquency. Make sure your central station is aware of the application of this

reporting code.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Comentários a estes Manuais

Sem comentários

DSC Power608 Especificações Página 44

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC Power608