DSC NT9005 V1.0 Especificações descarregar pdf (Página 29)

OFF Audible Exit Fault Disabled 

For [*][9] arming, if Audible Exit fault is enabled, a vio-

lated zone will begin Entry Delay as indicated. If this

option is disabled, a violated delay zone at the end the

Exit Delay will cause an instant alarm.

7 ON Event Buffer follows Swinger Shut-

down

!

When an event reaches the swinger shutdown limit pro-

grammed in section [370], it will not log events to the

event buffer and communicate them to the central sta-

tion, until swinger shutdown is reset. This prevents the

panel from overwriting the buffer with useless events and

flooding the central station with calls.

☞

The event buffer can be uploaded with DLS-3 software.

OFF Event Buffer logs Events past Shutdown 

8 ON Temporal 3 Fire Signal Enabled 

All fire bells will sound in the three temporal pattern

described in NFPA 72 (0.5 seconds ON, 0.5 seconds OFF,

0.5 seconds ON, 0.5 seconds OFF, 0.5seconds ON, 1.5

seconds OFF).

OFF Standard Pulsed Fire Signal !

All fire bells will sound with the standard 1 sec ON, 1 sec

OFF fire bell cadence.

☞

Zone definitions [87], [88], and [F] key will use this if

enabled.

[014] Second System Option Codes

1 ON Bell Squawk on Arm/Disarm Enabled 

The bell will sound a single squawk when armed in any man-

ner, and a double squawk upon disarming the system. If

there are alarms in memory, the bell will emit a series of three

squawk pairs to indicate the alarm memory.

OFF Bell Squawk on Arm/Disarm Disabled 

The bell output will not squawk when the system is armed or

disarmed in any way.

2 ON Bell Squawk During Auto-arm Enabled 

The bell output will sound a single squawk every 10 seconds

during the 1 minute Auto-arm pre-alert time.

OFF Bell Squawk During Auto-arm Disabled 

The bell output will not be activated during the 1-minute

Auto-arm pre-alert time.

3 ON Bell Squawk On Exit Delay 

The bell output will squawk once per second during the Exit

Delay time. The bell will also sound 3 squawks per second for

the final 10 seconds.

OFF No Bell Squawk On Exit Delay 

This audible option does not apply to Stay and No Entry Arm-

ing Modes.

4 ON Bell Squawk On Entry Delay 

The bell output will pulse with the same timing as the keypad

buzzer during the Entry Delay time.

OFF No Bell Squawk On Entry Delay 

5 ON Bell Squawks On Trouble 

Whenever there is a Trouble condition annunciated on the

system keypads, the bell will squawk 2 times every 10 sec-

onds (as per the keypad buzzer). The bell will be silenced

when the keypad beeps are silenced (any key pressed on key-

pad).

OFF No Bell Squawks On Trouble 

6 ON Audible Exit With Urgency 

The keypad will sound a pulsing tone (once per second) dur-

ing the Exit Delay. For the last 10 seconds of the Exit Delay,

the keypad and bell/siren (if enabled) will sound a different

tone (3 tones per second).

OFF Silent Exit Delay 

7 ON Exit Delay Termination Enabled 

The Exit Delay will be terminated when a Delay 1 Zone for the

entry/exit door or area is restored. Audible options associated

with the Exit Delay will be silenced when the Exit Delay is ter-

minated. Force-Armable Delay 1 type zones will also termi-

nate the Exit Delay.

OFF Exit Delay Termination Disabled 

The Exit Delay timer will continue to count even after the

Delay Zone for the entry/exit door or area is restored. All

audible options associated with the Exit Delay will function

until the time programmed for the Exit Delay has elapsed.

8 ON Fire Bell is Continuous 

For all Fire type alarms, the bell output will sound until an

access code is entered to silence the alarm or disarm the sys-

tem regardless of the time programmed for bell timeout in

section [005].

OFF Fire Bell follows Timeout 

For all Fire type alarms, the bell output will sound for the

length of bell timeout or until an access code is entered.

[015] Third System Option Codes

1 ON [F] Key Enabled 

Pressing and holding the [F] key for 2 seconds will generate a

Fire alarm. The keypad will sound a set of 3 beeps to

acknowledge the valid alarm and the bell or siren will sound

with a pulsing tone for the length of bell timeout. An alarm

reporting code (if programmed) will be transmitted.

☞

If enabled, this key will generate alarms at all times.

OFF [F] Key Disabled 

The [F] key will not sound or report an alarm when pressed.

2 ON [P] Key Audible (Bell/Beeps) 

When a valid [P] key alarm is generated, the keypad buzzer

will sound a series of 3 beeps to acknowledge the alarm and

the bell or siren will sound for the length of bell timeout.

OFF [P] Key Silent 

[

[005] System Times

Default

Entry Delay 1 030 I___I___I___I (000 - 255) seconds

Entry Delay 2 045 I___I___I___I (000 - 255) seconds

Exit Delay 060 I___I___I___I (000 - 255) seconds

Bell Cut-off 004 I___I___I___I (000 - 255) minutes

[006-008] Access Codes

☞

All codes can be either 4 or 6 digits in length. The default is 4

digits. See section [701], option 5.

User codes and Duress codes are programmed via [*][5] pro-

gramming.

[006] Installer’s Code

Change value to prevent unauthorized access to system.

Default 5555 I___I___I___I___I___I___I

[007] Master Code

[*]

Function

The Master Code can perform any function. This code can be used

to program all access codes including the duress codes. If the Mas-

ter Code Not Changeable option in section [015][6] is enabled,

users will not be able to change the Master code.

Default 1234 I___I___I___I___I___I___I

[008] Maintenance Code

This is an Arm/Disarm only code. It cannot be used to activate [*][7]

outputs, program other user codes or enter the [*][6] menu. Open-

ings or closings using this code report as a Special Opening/Clos-

ing and will log to the event buffer as Maintenance Code.

Default AAAA I___I___I___I___I___I___I

[009-011] PGM Output Programming

PGM Outputs

1, 2

Programmed in section [009]. Attributes are

programmed in sections [141], [142]

PGM Outputs

11, 12, 13, 14

Programmed in section [011]. Attributes pro-

grammed in sections [151]-[154]

Unless indicated otherwise, attributes are as indicated below.

Attribute numbers not mentioned in the default section have

no impact on operation and are typically defaulted OFF.

Attribute Function

ON OFF

6-8

Enabled

Future Use

True Output

Output Pulsed

Code Required

Future Use

Disabled

Inverted Output

ON/OFF

No Code Required

01 Fire and Burglary Output - causes the PGM output to

switch to ground upon any bell activity. The output will be

pulsed or steady depending on the type of bell activity. The

output follows the time programmed for the bell time-out.

Default Attributes: 1,3 ON 2 OFF

See sections [005] option [4] and [014] option [8].

02-04 Not Used

05 Armed Status - The PGM output switches to ground when

the system is armed (beginning of the exit delay). The output

goes high (open) when the panel is disarmed.

Default Attributes: 1,3 ON 2,5 OFF

06 Ready to Arm - The PGM output switches to ground as long

as the system is Ready to Arm (all non force-armable zones

on the system are restored). Once an access code is entered

to arm the system and the exit delay begins, the PGM output

is deactivated.

Default Attributes: 1,3 ON 2 OFF

07 Keypad Buzzer Follow Mode - The PGM output will go low

when the keypad buzzer is activated by the events described

below. The PGM output will go low for as long as the keypad

buzzer is active.

- 24-Hr Supervisory Buzzer Zone

- Auto-arm Pre-alert (1 minute)

- Entry Delay

- Door Chime

Default Attributes: 1,3 ON 2 OFF

08 Courtesy Pulse - This option provides an output which fol-

lows the entry and exit times. It can be used to turn on a

courtesy light near the exit door for the duration of the entry/

exit times. Upon activation during an entry delay, the output

will remain active for 2 minutes past the entry or exit times to

allow enough time for complete and safe entry or exit to or

from the premises.

Default Attributes: 1,3 ON 2 OFF

09 System Trouble Output (with Trouble Options) - The

PGM output switches to ground when any of the selected

Troubles are detected on the system. The output will deacti-

vate when all of the selected Troubles are restored. The

attributes normally programmed in sections [141] to [154]

are replaced with the following options.

Default Attributes: ALL ON

Attribute Function

Service Required

A.C. Fail

Telephone Line Monitoring (TLM) Fault

Communications (Failure to Communicate)

Zone (Fire) Fault

Zone Tamper

Zone Low Battery

Loss of Clock

WWW.DIYALARMFORUM.COM

1 2 ... 24 25 26 27 28 29 30

WWW.DIYALARMFORUM.COM 1

Comentários a estes Manuais

Sem comentários

DSC NT9005 V1.0 Especificações Página 29

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC NT9005 V1.0