DSC SYSTEM MASTER PC4000 Manual de Instruções descarregar pdf (Página 4)

MONITORING

This system is capable of transmitting alarms, troubles, and emergency information

over telephone lines to a monitoring station. If you inadvertently initiate an alarm,

immediately call the monitoring station to prevent an unnecessary response.

NOTE

: The monitoring function must be enabled by the installer before it becomes

functional.

GENERAL SYSTEM OPERATION

Your security system is made up of a PC4000 and one or more LCD-4500 and various

detectors and sensors. The DSC control panel will be mounted out of the way in a

utility room or basement. The metal cabinet contains the system electronics, fuses

and stand-by battery. There is normally no reason for anyone but the installer or

service person to have access to the control panel. The LCD-4500 keypads have an

audible indicator, an alphanumeric LCD, (Liquid Crystal Display), and command entry

keys. The keypad is used to send commands to the system and to display the current

system status. The keypad(s) will be mounted in convenient locations inside the

protected premises close to the exit-entry doors.

The security system has several zones or areas of protection and each of these

zones will have one or more detection sensors connected to it (motion detectors,

glassbreak detectors, door contacts or shock sensors). When a sensor is in alarm,

the zone in alarm will be displayed on the LCD-4500.

TROUBLE AND ARMED LED DISPLAYS

The LCD-4500 has a yellow LED on the right side of the keypad which represents

the trouble status of the panel. There is a red LED just below the yellow one which

represents the armed status of the panel.

SYSTEM MASTER CODES

System Master Codes are used for arming and disarming the control panel, for

viewing the armed/disarmed status of the partitions, for programming additional

security codes and for entering ‘user functions’. See [✱][5] User Programming

Commands for programming System Master Codes. In the disarmed state, entering a

Master Code will cause a nine selection menu to be displayed as follows:

[0]Arm Partition [1]Arm Diff Part. [2]Disarm Diff Part

[3]View Partitions [4]Set System Time [5]Set System Date

[6]System Reset [7]Enable DLS Window [8]Previous Menu

[0] Arm Partition will arm the partition the keypad is on. The keypad will display the

message ‘Exit delay in progress’ and the armed light will come on.

[1] Arm Diff Part. will show a menu of the other partitions and their armed/disarmed

status. R means it is ready to be armed, N means it is not ready to be armed,

and A means the partition is armed. If the partition status is R, then this partition

can be selected to be armed. If a partition is not enabled, it will not be displayed.

MAINTENANCE

With normal use, the system requires minimum maintenance. The following points

should be observed.

1.Do not wash the keypad with a wet cloth. Light dusting with a barely damp cloth

should remove normal accumulations of dust.

2.The battery/bell test is designed to determine battery condition, however it is

recommended that the stand-by batteries be replaced every three years.

3.For other system devices such as smoke detectors, passive infrared, ultrasonic or

microwave motion detectors or glassbreak detectors, consult the respective

manufacturer’s literature for testing and maintenance.

LIMITED WARRANTY

Digital Security Controls Ltd. warrants that for a period of twelve months from the

date of purchase, the product shall be free of defects in materials and workmanship

under normal use and that in fulfillment of any breach of such warranty, Digital

Security Controls Ltd. shall, at its option, repair or replace the defective equipment

upon return of the equipment to its factory. This warranty applies only to defects in

parts and workmanship and not to damage incurred in shipping or handling, or

damage due to causes beyond the control of Digital Security Controls Ltd. such as

lightning, excessive voltage, mechanical shock, water damage, or damage arising

out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in

lieu of any and all other warranties, whether expressed or implied and of all other

obligations or liabilities on the part of Digital Security Controls Ltd. This warranty

contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor

authorizes any other person purporting to act on its behalf to modify or to change this

warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct or indirect or

consequential damages, loss of anticipated profits, loss of time or any other losses

incurred by the buyer in connection with the purchase, installation or operation or

failure of this product.

WARNING

Digital Security Controls Ltd. recommends that the entire system be completely

tested on a regular basis. However, despite frequent testing, and due to, but not

limited to, criminal tampering or electrical disruption, it is possible for this product to

fail to perform as expected.

1 2 3 4 5 6 7 8 9 ... 19 20

Comentários a estes Manuais

Sem comentários

DSC SYSTEM MASTER PC4000 Manual de Instruções Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC SYSTEM MASTER PC4000