DSC Power832 PC5O15 Manual de Instalação descarregar pdf (Página 21)

K E Y P A D C O M M A N D S

[06] - [✱]+[4] Door Chime On/Off

This function key provides the user a simple method for turning the Door Chime feature on and off

(See Section

3.4 “[

✱

] Commands, [

✱

] [4] Door chime on/off”)

[07] - [✱]+[6]...[4] System Test

This function key provides the user with a simple method for testing the system

(See Section 3.4 “[

✱

]

Commands, [

✱

] [6] User functions”)

. A valid Master Code is required to perform this command.

[08] - [✱]+[1] Bypass Mode

This function key provides the user with a simple method for entering the Bypass Mode. If a access code is

required it must be entered before bypassing can be performed

(See Section 3.4 “[

✱

] Commands, [

✱

] [1] Zone

Bypass”)

[09] - [✱]+[2] Trouble Display

This function key provides the user with a simple method for entering the Trouble Display Mode

(See Section 3.4

“[

✱

] Commands, [

✱

]+[2] Trouble display”

[10] - [✱]+[3] Alarm Memory

This function key provides the user with a simple method for entering the Alarm Memory Display Mode

(See

Section 3.4 “[

✱

] Commands, [

✱

] [3] Alarm memory”)

[11] - [✱]+[5] Programming Access Codes

This function key provides the user with a simple method for programming access codes. After this key is

pressed a valid System Master or Partition Master will have to be entered before the panel will allow

programming to be performed

(See Section 3.4 “[

✱

] Commands, [

✱

] [5] Programming Access Codes”)

[12] - [✱]+[6] User Functions

This function key provides the user with a simple method for programming User Functions. After this key is

pressed a valid System Master or Partition Master must be entered before the panel will allow User Functions to

be performed

(See Section 3.4 “[

✱

] Commands, [

✱

] [6] User functions”)

[13] - [✱]+[7]+[1] Command Output Option 1

This function key provides the user with a simple method for activating a PGM Output programmed as

Command Output Option 1

(See Section 5.10 “PGM Outputs”)

. By default, after this key is pressed a valid

access code must be entered

(See Section 3.4 “[

✱

] Commands, [

✱

] [7] Command output functions”)

[14] - [✱]+[7]+[2] Smoke Detector Reset

This function key provides the user with a simple method for activating a PGM output programmed as either

option [03] Sensor Reset, [04] 2-wire Smoke Support or [20] Command Output option 2.

[15] - General Voice Prompt Help

This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are being used.

When the function key is pressed, the intercoms will perform a Help page. The user must then press the Page/

Answer button on any intercom station to begin the help session with the Escort.

For more information, please refer to the PC5928 Installation Manual.

[16] - [✱]+[0] Quick Exit

Same as described in Function Keys - Section 3.5.

[17] - [✱]+[1] Reactivate Stay/Away Zones

This function key provides the user with a simple method for adding Stay/Away zones back into the system

(see

Section 3.4 “[

✱

] Commands, [

✱

] [1] Reactivate Stay/Away zones”)

[18] Identified Voice Prompt Help

This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are being used.

When the function key is pressed, the Escort will begin a help session from the intercom station programmed as

closest to the keypad. In order for this option to function, you must program PC5928 Section [802], subsection

[14] “Keypad Port Assignments.” For more information, please refer to the PC5928 Installation Manual.

Note: This function key cannot be programmed for PC55XXZ LED keypads with software version 1.0.

[19] - [✱]+[7]+[3] Command Output 3

[21] - [✱]+[7]+[4] Command Output 4

Function Keys [19] and [21] provide the user with a simple method of activating an output programmed as

Command Output Option 3 or 4.

[22] - Active Camera Monitor Selection

This function key is for use with the PC5108L Downlook Interface/Camera Monitor Module. For instructions on

the function key use, see the PC5108L Installation Manual.

[23] - Bypass Recall

Pressing this function key will recall the last group of bypassed zones. The function key will follow the Code Required

for Bypass option. If the option is enabled, a valid access code with the Bypass attribute enabled must be entered

after the function key is pressed. For instructions on zone bypassing, see the PC5015 Instruction Manual.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 47 48

Comentários a estes Manuais

Sem comentários

DSC Power832 PC5O15 Manual de Instalação Página 21

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC Power832 PC5O15