DSC Power832 PC5O15 Manual de Instalação descarregar pdf (Página 10)

G E T T I N G S T A R T E D

Connect the PC5015 and modules that use the telephone line(s) in the following order:

For example, if you are installing a PC5015 with a LINKS1000 and a PC5928 Intercom module, connect the

incoming line to the LINKS1000, then from the LINKS1000 to the PC5015, then from the PC5015 to the PC5928

Intercom and then from the PC5928 to the house telephones

For prFor pr

For pr

oper operation theroper operation ther

oper operation ther

e must be no other telephone equipment connected between the contre must be no other telephone equipment connected between the contr

e must be no other telephone equipment connected between the contr

ol panelol panel

ol panel

and the telephone company facilitiesand the telephone company facilities

and the telephone company facilities

. .

Do not connect the alarDo not connect the alar

Do not connect the alar

m panel communicator to telephone linesm panel communicator to telephone lines

m panel communicator to telephone lines

intended for use with a Fintended for use with a F

intended for use with a F

AX machine. These lines may incorporate a voice filter which disconnects theAX machine. These lines may incorporate a voice filter which disconnects the

AX machine. These lines may incorporate a voice filter which disconnects the

line if anything other than Fline if anything other than F

line if anything other than F

AX signals arAX signals ar

AX signals ar

e detected, re detected, r

e detected, r

esulting in incomplete transmissionsesulting in incomplete transmissions

esulting in incomplete transmissions

2.3 Wire Routing for Power & Non-Power Limited

All wiring entry points are designated by the arrows. All circuits

are classified UL installation power limited except for the battery

leads which are not power limited.

A minimum ¼” (6.4mm) separation must be maintained at all

points between power limited and non-power limited wiring and

connections.

irir

e entre entr

e entr

y for power limited wiring must be separated byy for power limited wiring must be separated by

y for power limited wiring must be separated by

a difa dif

a dif

ferfer

fer

ent entrent entr

ent entr

y access fry access fr

y access fr

om non-power limited wiring.om non-power limited wiring.

om non-power limited wiring.

2.4 Keybus Operation and Wiring

The Keybus is used by the panel to communicate with all modules

connected and by the modules to talk to the panel. The RED and

BLK terminals are used to provide power while YEL and GRN are

clock and data.

The 4 Keybus terThe 4 Keybus ter

The 4 Keybus ter

minals of the panel must be connected tominals of the panel must be connected to

minals of the panel must be connected to

the 4 Keybus terthe 4 Keybus ter

the 4 Keybus ter

minals or wirminals or wir

minals or wir

es of all modules.es of all modules.

es of all modules.

The following conditions apply:

• Keybus should be run in minimum 22 gauge quad (0.5mm), two

pair twist preferred

• the modules can be home run to the panel, connected in series or can be T-tapped

• any module can be connected anywhere along the Keybus, you do not need a separate Keybus wire run for

keypads, zone expanders etc.

• no module can be more than 1,000'/305m (in wire length) from the panel

• shielded wire is not necessary unless wires are run in an area that may present excessive RF noise or

interference

Example of Keybus Wiring

PANEL

500’

150’

PANEL

500’

150’

NOTE: Module (A) is wired correctly as it is within 1,000'/305m of the panel,

in wire distance.

Module (B) is wired correctly as it is within 1,000'/305m of the panel,

in wire distance

Module (C) is NOT wired correctly as it is further than 1,000'/305m

from the panel, in wire distance.

2.5 Current Ratings - Modules and Accessories

In order for the Power 832 system to operate properly, the power output capabilities of the main control and

expansion devices must not be exceeded. Use the data presented below to ensure that no part of the system is

overloaded and cannot function properly.

System Outputs (all 12 V

DC)

• PC5015 VAUX: 550 mA. Subtract the listed rating for each keypad, expansion module and accessory

connected to VAUX or Keybus.

Keybus

NOTE: A minimum 1/4" (6.4mm) separation

must be maintained at all points between

power limited and non-power limited wiring

and connections.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 47 48

Comentários a estes Manuais

Sem comentários

DSC Power832 PC5O15 Manual de Instalação Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC Power832 PC5O15