DSC Power432 PC585 Manual de Instalação descarregar pdf (Página 31)

Restore PC5132 to Default Programming . . . . Section [996]

Restore PC5400 Printer to Default ProgrammingSection [997]

Restore Panel to Default Programming . . . . . . Section [999]

5.31 Installer’s Lockout

If Installer’s Lockout is selected, a hardware default cannot

be performed. If a software default is performed, all program-

ming will restore to factory default.

If Installer’s Lockout Disable is selected, the panel will

restore all programming to factory defaults when a hardware

or software default is performed on the main control panel.

To enable or disable Installer’s Lockout, perform the following:

1. Enter the Installer’s Programming mode.

2. Enter the appropriate programming section: [990] or [991].

3. Enter the Installer’s Code.

4. Re-enter the appropriate programming section: [990] or

[991].

Installer Lockout Enable. . . . . . . . . . . . . . . . . . Section [990]

Installer Lockout Disable . . . . . . . . . . . . . . . . . Section [991]

5.32 Walk Test (Installer)

The Installer Walk Test can be used to test the alarm state of

each zone of the panel. The walk test cannot be used to test

zone type [24].

Before beginning the walk test, ensure the following condi-

tions are met:

1. The panel is disarmed

2. The Keypad Blanking option is disabled (section [016]:

[3])

3. The Fire Bell is Continuous option is disabled (section

[014]: [8])

4. The Transmission Delay is disabled, if Transmission

Delay is not required (section [370])

NOTE: Fire Troubles are not supported in Walk Test.

To perform a walk test:

Step 1 - Enter Installer Programming

Step 2 - Enter Section [901]

When any zone is violated the panel will activate the Bell Out-

put for two seconds, log the event to the event buffer and

communicate the alarm to central station.

Test each zone several times. Check the event buffer to

ensure that all zones and FAP keys are functioning properly.

NOTE: Zones with the Force Arm attribute enabled, will not

cause the Ready light to go out when they are violated.

To stop the test:

Step 1 - Enter Installer Programming

Step 2 - Enter section [901]

NOTE: The alarm memory is cleared upon entering Walk Test

mode. When the walk test is complete, the Alarm Memory light

will remain lit, but there will be no alarms in memory. The light

will turn off the next time the panel is armed.

Installer Walk Test Enable/Disable . . . . . . . . . . Section [901]

5.33 Daylight Savings Time

Daylight Savings Time Enabled. At 2:00am on the first Sun-

day in April, the panel clock will be set forward one hour to

3am. At 2:00am on the last Sunday in October, the panel clock

will be set back one hour to 1:00am. Events programmed to

occur between 2:00am and 3:00am will not occur on the last

Sunday in April. Events programmed to occur between 1:00

and 2:00am will occur twice on the last Sunday in October.

Daylight Savings Time Disabled. The panel will make no

automatic time adjustments for Daylight Savings Time.

NOTE: Auto-arm and test transmissions should not be

attempted between 2:00am and 3:00am, as they will be

missed on the first Sunday in April. Events programmed to

occur between 1:00am and 2:00am will occur twice on the last

Sunday in October.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 55 56

Comentários a estes Manuais

Sem comentários

DSC Power432 PC585 Manual de Instalação Página 31

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC Power432 PC585