DSC PTK5507 Manual de Instalação descarregar pdf (Página 2)

The PTK5507 keypad can be used on security systems with up to 64

zones. These keypads are compatible with the latest version of the

Power Series V4.2+security systems.

Specifications

• Temperature range: -10°C to +55°C (14°F to 131°F)

• Humidity (MAX): 93%R.H. non-condensing

• Plastic enclosure protection degree: IP30, IK04 (touchscreen

excluded)

• Voltage rating: 12VDC nominal

• Connects to control panel via 4-wire Keybus

• Keybus distance: 60 m (200 ft.) (max.); keybus distance in extra

power mode: 33.5 m (110 ft)

• Up to 8 keypads per system

• PTK5507 Current draw: 200 mA (standby)/300 mA (activated)/

400mA Extra Power Mode

• Wall mount tamper

• 5 programmable function keys

• Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), AC

(Green LED)

• Touchscreen display: 8.5" x 5.1" x 0.8" [127.9 mm (L) x 195

mm (W) x 20.35 mm (D)]

• SD card slot: holds any standard Secure Digital (SD) card* (32 x

24 x 2.1 mm) containing photos

*If necessary, the SD card can be formatted to file system FAT16

or 32 using a PC. The maximum size SD card supported is 32GB.

• Wiring: standard four-wire connection

• Viewing angle: horizontal viewing angle: 70° (typ.)

• Vertical viewing angle: 50° (top), 70° (bottom) (typ.)

• Brightness: 280 cd/m

Unpacking

The Power keypad package includes the following parts:

Mounting

You should mount the keypad where it is accessible to designated

points of entry and exit. Once you have selected a dry and secure

location, perform the following steps to mount the keypad.

Mount and Wire Keypad

1. Remove the SD card before opening the touchscreen (see

Figure 1).

WARNING: Disassembling the touchscreen

without removing the SD card will damage

the unit.

2. Remove screw at the bottom of the keypad.

3. Insert screwdriver into slots and pry up to remove cover.

Figure 1 - Removing the backplate

4. Secure keypad backplate to wall using mounting holes.

(See Figure 2.) Use all 4 screws provided unless mounting

on a single gang box. Use the plastic anchors supplied if the

unit is to be mounted on drywall. If using the keypad

tamper, secure the tamper plate to the wall with a screw.

Figure 2 - Mounting the backplate

5. Run wire through wiring slot. Connect keybus wiring to

keypad (see Wiring section).

6. Place keypad into backplate, ensuring the wire is pushed

back into the wall as much as possible. Route the wire

inside the keypad ensuring high components are avoided.

Snap the front assembly closed, ensuring that there is no

pressure to the keypad from the wire below.

NOTE: If any tension is found between the

front keypad assembly and wiring, please

open the keypad, re-route the wire and close

again. Repeat these steps until the keypad is

closed properly.

Wiring

1. Before wiring the unit, ensure that all power (AC

transformer, telecommunication network, and battery) is

disconnected from the control panel.

2. Wrap the Keybus wires through the ferrite core (see Figure

3); one turn is enough. The ferrite core shall be installed as

close to the touchscreen as the installation will allow.

Figure 3 - Ferrite core

English

Installation Instructions

•One Power keypad •1 tamper switch

•Five mounting screws •Installation Instructions

•Five anchors for wall-mounting

screws

•User Manual

gently

push

press

eject

mounting hole

wiring slot

mounting hole

hole for

tamper

screw

1 2 3 4 5 6 7 ... 31 32

Comentários a estes Manuais

Sem comentários

DSC PTK5507 Manual de Instalação Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC PTK5507