DSC Power8 PC5OO5 Manual de Instalação descarregar pdf (Página 35)

P R O G R A M D E S C R I P T I O N S

[11] System Tamper

The PGM Output will activate when any Tamper condition is present and will deactivate when

all Tamper conditions are cleared.

[12] TLM and Alarm

The PGM Output will activate when a telephone line fault condition is present AND an alarm

occurs. The PGM Output will remain active until an access code is entered. The output will activate for both audible

and silent alarms if a TLM trouble is present.

This output will activate for all audible and silent alarms except Duress.

[13] Kissoff The PGM Output will activate for two seconds after the panel receives the kissoff from the central station.

[14] Ground Start

(Shall not be enabled on UL Listed systems)

The PGM Output will activate for two seconds

before the panel attempts to dial to obtain dial tone on Ground Start telephone equipment. Two second pauses should

be inserted at the beginning of the phone number when using this option.

[15] Remote Operation (DLS-1 Support)

This output can be activated and deactivated remotely using DLS software.

[16] LINKS1000 Support (PGM1 Only) The PGM output will be used as a data wire to communicate phone

number information for the LINKS1000 cellular unit.

[17] Away Armed The PGM will activate when the system is armed with the Stay/Away zones activated.

[18] Stay Armed The PGM will activate when the system is armed with the Stay/Away zones bypassed.

[19] [✱] [7] [1] Command Output Option #1

[20] [✱] [7] [2] Command Output Option #2 Press [

✱]

[7] [2] [Access Code, if required] to activate any output

programmed as one of PGM output option [03] or [20].

Traditionally, [✱] [7] [2] has been reserved for resetting smoke detectors. Smoke detectors should now be

programmed as output [03] “Sensor Reset”.

Only ONE of options [03] Sensor Reset, [04] 2-Wire Smoke and [20] [

✱

] [7] [2] Command Output Option

#2 may be programmed on the same system.

[21] [✱] [7] [3] Command Output Option #3

[22] [

✱✱

✱] [7] [4] Command Output Option #4 These outputs are user-initiated by entering [✱] [7] [1-4] at any

keypad. When any output is activated, three acknowledgment beeps are heard.

[23] Silent 24 Hour (PGM2 Only) A Panic button may be placed on the PGM2 terminal for use as a silent 24

hour Panic. The keypad will not indicate the alarm in any way and the Bell will remain silent but the PGM2 Alarm

reporting code will be sent to the central station. PGM output option [23] will not activate other programmable

outputs of any kind. This input does not follow Swinger Shutdown.

[24] Audible 24 Hour (PGM2 Only) A Panic button may be placed on the PGM2 Terminal for use as an Audible

24 Hour Panic. When the button is pressed, LCD keypads will indicate “System in Alarm”, the bell will sound until

the Bell Cut-off expires, and the PGM2 Alarm reporting code will be sent to the central station. PGM output option

[24] will not activate other programmable outputs except for outputs programmed as [01]. This input does not

follow Swinger Shutdown.

Main Board PGM Outputs ..................................... Section [009]

PC5208 PGM Output Options ............................... Section [010]

PC5204 PGM Output Options ............................... Section [011]

5.10.2 PGM Output Attributes

In addition to programming the output type, you must also program the PGM output attributes for each output.

PGM output options [09] “System Trouble” and [10] “Latched System Event” have their own unique set of

attributes listed below the description of each output type.

PGM output options [01], [03], [05]-[08], [11]-[24] have the following attributes:

Attribute ON OFF

[1] Partition 1 controls event Partition 1 Does Not

[2] Partition 2 controls event Partition 2 Does Not

[3] True Output Inverted Output

The output energizes when activated The output will de-energize when activated.

(except for Option [03] Sensor Reset).

[4] 5 Second Pulse Output ON/OFF

The output will activate once for five The output will turn ON and OFF when initiated by

seconds when initiated by the user. the user

(only applicable to options [19] to [22]).

[5] Access Code Req. No code Req.

The output requires a code for activation. No code required.

(only applicable to keypad-activated outputs)

PGM attributes return to their default settings when you change PGM output options. Please see the

programming worksheets for a list of the default settings for each PGM output type.

Care should be taken in selecting the normal and active states of each PGM output to ensure that an

undesirable output state does not occur after a loss and restore of AC power.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 45 46

Comentários a estes Manuais

Sem comentários

DSC Power8 PC5OO5 Manual de Instalação Página 35

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DSC Power8 PC5OO5